The current flange-style basket seats flat
- The basket drops into the washer-fluid opening without force
- The metal rim rests evenly on the filler-neck ledge
- The original washer-fluid cap closes and locks normally above it
mysite
Rain Scraper Filter for Model 3 Highland & Model Y
Rain Scraper Filter for Model 3 Highland & Model Y
Regular price
$3.99
Regular price
$11.99
Sale price
$3.99
Shipping calculated at checkout.
Quantity
Couldn't load pickup availability
Drop-in washer-fluid fill-neck strainer
Stop debris at the fill point.
Place this removable stainless-steel mesh basket inside a compatible windshield-washer fluid opening. It catches leaves, grit and other visible particles while the cap is open or fluid is being added—before they can be poured into the reservoir.
- 304 stainless-steel mesh
- No adhesive
- Removable + washable
- 1 filter basket
The product in five points
A simple barrier for a frequently overlooked opening.
- Filters as you refillThe basket sits below the washer-fluid cap and intercepts visible solid debris that could otherwise enter with the fluid.
- Fine stainless-steel mesh304 stainless steel provides a rigid, corrosion-resistant screen for repeated contact with washer fluid and rinse water.
- No glue or permanent changeThe flange rests at a compatible filler neck without adhesive, drilling or modification to the vehicle.
- Lift out for cleaningRemove the basket with the cap open, discard captured debris away from the reservoir and rinse the mesh before reinstalling.
- Preventive—not a repair partIt can reduce debris introduced at the fill opening, but it cannot clean a contaminated tank, unblock an existing nozzle or repair a washer-system fault.
Check the opening before ordering
Fit is determined by the washer-fluid filler neck and cap clearance.
Remove it if the geometry conflicts
- The rim rocks, tilts or remains raised above the opening
- The mesh must be crushed, bent or trimmed to enter
- The original cap becomes difficult to close or no longer seals normally
Listed for Model 3 Highland and compatible Model Y washer-fluid openings.
Tesla filler-neck and surrounding-panel geometry can vary by model year, factory and market. Model Y Juniper, Model YL and other Model 3 / Model Y configurations should be confirmed from the current flange-style product and installation photos. This listing has one size and no separate vehicle variants.
Know exactly where it works
This is a washer-fluid fill strainer—not a rain gutter screen.
Install it under the cap marked with the windshield-and-spray symbol. Its job is limited and useful: catch visible solid debris at that opening.
- Helps intercept leaves, grit and fragments during a refill
- Lets washer fluid pass through the mesh into the reservoir
- Remains accessible whenever the original cap is opened
Add a physical screening step
It reduces the chance of pouring larger visible contaminants through the filler neck and gives you a removable place to collect them.
Replace washer-system maintenance
It does not filter the air intake or under-hood rain drains, purify washer fluid, dissolve residue, increase pump pressure, improve worn wiper blades or guarantee that no nozzle will ever clog.
Install and refill
Clean around the opening first, then pour slowly.
- Park and identify the capOpen the hood while parked and locate the windshield-washer fluid cap by its spray symbol. Do not confuse it with another service opening.
- Clean before openingWipe loose dust and leaves away from the cap so they cannot fall into the filler neck when it is removed.
- Seat the basketLower the clean mesh basket into the opening without force and confirm the flange rests flat on the available ledge.
- Add proper fluid slowlyPour manufacturer-appropriate washer fluid at a controlled rate. Fine mesh can slow the flow; pause if fluid begins pooling near the rim.
- Clear and closeRemove captured debris, reseat the clean basket and close the original cap. Stop using the basket if the cap cannot close normally.
Never push captured debris through the mesh.
Lift the basket out carefully and empty it away from the open reservoir. Keep tools, fingers and loose objects out of the filler neck, and avoid handling damaged mesh with bare hands.
Maintenance that preserves the benefit
A full or dirty screen becomes a bottleneck.
Look before every refill
Check for trapped leaves, sediment, deformation and sharp or separated mesh before pouring fluid.
Clean outside the vehicle
Remove the basket, rinse from the clean side toward the debris side, and use a soft brush only if necessary.
Dry and seat it flat
Allow it to drain, reinstall without forcing and verify the original cap still closes exactly as it did before.
Product facts
One removable screen with a clearly defined job.
| Item | Current product information |
|---|---|
| Product type | Windshield-washer fluid filler-neck strainer / filter basket |
| Current shape | Round stainless-steel mesh basket with a flat support flange, as shown in the current main image |
| Listed application | Model 3 Highland and compatible Model Y washer-fluid openings; verify the actual filler-neck and cap geometry for Model Y Juniper, Model YL and other vehicle configurations |
| Material / color | 304 stainless steel / silver |
| Installation | Drop-in, removable placement; no adhesive, drilling or tools |
| Function | Intercepts visible solid debris at the washer-fluid fill opening while allowing fluid to pass through |
| Package | 1 × washer-fluid filter basket |
| Care | Remove and rinse as needed. Replace the product if the flange or mesh is bent, split, loose or sharp. |
Before you order
Washer-fluid strainer FAQ
Where does this filter go?
It sits inside a compatible windshield-washer fluid filler neck, directly under the cap marked with the windshield-and-spray symbol. It is not installed in the cabin-air intake or an under-hood rainwater drain.
Will it fit every Model 3 and Model Y?
No single drop-in basket should be assumed to fit every filler-neck revision. The current listing shows a flange-style basket for Model 3 Highland and compatible Model Y openings. Compare your opening, ledge and cap clearance with the current photos before ordering.
What about Model Y Juniper or Model YL?
Use the filler-neck geometry as the final check. The basket must drop in without force, rest flat and allow the original cap to close normally. Do not bend or trim it to make an incompatible opening work.
Can it prevent every washer nozzle blockage?
No. It helps stop visible debris introduced through the filler opening, but blockages can also come from unsuitable fluid, dried deposits, contaminated tanks, freezing, pump or hose problems and nozzle damage.
Why does washer fluid pass through more slowly?
Fine mesh restricts flow more than an open filler neck. Pour slowly and pause if fluid pools near the rim. A noticeably slower flow can also mean the screen needs cleaning.
Can I leave the basket installed under the cap?
Yes, provided it sits flat and the original cap closes and locks normally without extra force. Remove the basket if it changes cap operation or sealing.
Does it require adhesive?
No. The basket is designed to rest in a compatible filler neck and remain removable for cleaning. Do not glue or tape it in place.
What is included?
One 304 stainless-steel washer-fluid filter basket. Washer fluid, tools and decorative items shown in application images are not included.
Can I return it if the opening does not match?
Keep the basket clean, unused and unmodified while checking the opening. Do not bend, trim or glue it. Return eligibility is governed by the .
